Speed ovens combine microwave and convection in one cavity, which means real ventilation requirements and a circuit that can carry the load.
Speed Ovens
A speed oven pulls the current of a microwave and the heat of a convection oven at the same time. It needs its own circuit and it needs the cabinet ventilation openings the manual specifies, or it will nuisance-trip its thermal cutout.
We confirm both, set the unit square in the opening, secure it at the correct points, and run it through microwave, convection and combination modes before we call it complete.
What Sets Us Apart
Amperage checked against the model so the unit is never sharing a circuit it should not share.
The rear and top clearances the manual demands are confirmed, not assumed.
Flush frames and trim kits fitted so the appliance sits clean in the cabinet face.
Microwave, convection and combination cycles all run before we hand the unit over.
Our Process
We verify the dedicated circuit and confirm the cabinet ventilation matches the requirement.
The trim kit is assembled and the unit is set square in its opening.
Fastened at the correct points and connected, with the junction box left accessible.
Microwave, convection and combi are each tested, then the controls are demonstrated.
Brands We Install
Brand names and logos are the property of their respective owners and are shown to indicate the appliances we install. Bay Area Appliance Installation is an independent installer and is not an authorized dealer or agent of these manufacturers.
FAQs
Usually, if the opening and circuit match. Speed ovens tend to be deeper and hotter, so we always check the cabinet first.
Yes, in almost every case. Sharing a circuit is the most common cause of nuisance breaker trips with these units.
Yes, that is one of the most common configurations we install, and we handle the cabinet support it needs.
Related Services
Google Reviews from real Bay Area Appliance customers
We had a full Sub-Zero and Wolf package going into a new kitchen in Palo Alto and I was dreading install week. These guys measured everything two weeks before delivery, told our cabinet maker about a half inch problem with the refrigerator opening, and it got fixed before the appliances even shipped. Install day took one afternoon and everything worked. Genuinely the smoothest part of the entire remodel.
Hood install in a Berkeley Craftsman where the duct route was genuinely awkward. They ran rigid duct instead of the flex the previous quote wanted to use, and the difference in noise and airflow is enormous. It actually pulls steam now.
Full outdoor BBQ island in Novato. Grill, side burner, outdoor fridge and access doors. They pointed out the island was missing its vent panels and cut them in before setting the grill. That is a safety thing our contractor had missed entirely.
Wine column in Santa Rosa. Levelled it in both directions, ran both zones to temperature and told us to wait twelve hours before loading bottles. That kind of advice is why I would use them again.
Replaced a 20 year old cooktop with an induction unit and needed the electrical checked first. They looked at the panel, told me exactly what circuit I needed, and came back after the electrician finished. No upselling, no drama. The cutout was perfect and they cleaned the counter before leaving.
Washer and dryer install in Walnut Creek. They pulled the shipping bolts, levelled it properly and ran a spin cycle to prove it. Our old machine used to walk across the laundry room. This one has not moved an inch in four months.
Panel-ready dishwasher in Burlingame. The reveals match the cabinets exactly, which sounds like a small thing until you have seen one installed badly. They also ran a full cycle and watched the connections before signing off.
Double wall ovens into a stacked cabinet in Fremont. They checked the cabinet could take the weight and added support before lifting anything. The doors line up perfectly and it runs true to temperature.
Third floor condo in San Francisco with a freight elevator window of two hours. They handled the building paperwork, showed up early, and had the refrigerator in and running with time to spare. If you live in a building with rules, these are the people you want.
Miele built-in coffee unit plumbed into our kitchen island in Cupertino. They left enough slack in the line that the machine slides out for descaling, which our previous installer had not done on the old one. Small detail, huge difference.
LP conversion on a Wolf range at a property in Napa off the gas main. They used the actual Wolf kit, adjusted every simmer screw, leak tested it and labelled the unit. Very thorough and clearly knew the appliance well.
Micro-hood replacement in San Mateo. They noticed the previous installer had never rotated the blower, so it had been recirculating into the kitchen for years instead of venting outside. Fixed in ten minutes. Night and day difference.
Where We Work
Ready When You Are
Send us the model number and your city and we'll come back with a firm price, usually the same business day. Pre-measurement site visits available before you order.
(510) 240-2560Tell us the appliance and the city and we'll come back with a firm price, usually the same business day.
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
